Irrigation

Uniseals Fittings are used to attach pipe to just about any container in situation where bulkheads will not work. The most common use us on curved surfaces such as storage drums, buckets, and even other pipe. Uniseal acts as a Connector for Pipes. Learn More

These grommets can be used to replace old, worn grommets in your hydroponic systems and are essential components when making a system from scratch. Learn More

0.5 GPH Take-apart PC Emitter - Yellow w/ Outlet Nipple - 1/4" Barb Inlet Outlet can be used with .128 x 0.76 or .250 x .160 PE Tubing "Turbulent flow" PC (pressure compensating) drippers maintain their rated flow rate for 10-60 psi inlet pressure. These drippers can be used at the end of 1/4" tubing feeders or can be inserted directly into 1/2" hose. Ideal for heavy soil. 1 GPH Take-apart PC Emitter - Black w/ Outlet Nipple - 1/4" Barb Inlet Outlet can be used with .128 x 0.76 or .250 x .160 PE Tubing "Turbulent flow" PC (pressure compensating) drippers maintain their rated flow rate for 10-60 psi inlet pressure. These drippers can be used at the end of 1/4" tubing feeders or can be inserted directly into 1/2" hose. Ideal for medium soil (loam). 2 GPH Take-apart PC Emitter - Blue w/ Outlet Nipple - 1/4" Barb Inlet Outlet can be used with .128 x 0.76 or .250 x .160 PE Tubing "Turbulent flow" PC (pressure compensating) drippers maintain their rated flow rate for 10-60 psi inlet pressure. These drippers can be used at the end of 1/4" tubing feeders or can be inserted directly into 1/2" hose. Ideal for light soil (sandy). Learn More

Use to connect 3/4" tubing to 1/2" tubing. Learn More

Use to connect 1" tubing to 3/4" tubing. Learn More

4" Support Stakes Use to hold drippers in position next to plants to be watered. Position a support stake in the soil halfway between the center and the outer edge of the container. Place the dripper end securely in the yoke of the stake, allowing approximately 1" overlay. Adjust the depth of the stake leaving a minimum 1" air gap between the dripper outlet and the overflow rim of the container. 6" Support Stakes Use with 1/4" Tubing Use to hold tubing with drippers or tubing ends of the Hydroport Watering Manifold, Drip Star, Multiplex and Four Outlet Bubblers. Learn More

The professional tubing cutter has a hardened stainless steel blade that is designed to cut all flexible plastic hose/tubing up to 1.5" outside diameter. Designed for comfortable use. punch holes in 1/2", 5/8" or .710" hose to insert PC drippers or 1/4" fittings. Learn More

This hole punch is designed for comfortable use. It punches holes that are 1/2"", 5/8" or .710" hose to insert PC drippers or 1/4" fittings. Learn More

The Octa-Bubbler is an eight-outlet, pressure compensating, low-flow irrigation device. Along with 8 flow-controlled swivel barbed outlets, it has a 1/2” FPT inlet thread base for installation on standard risers, and a backflow prevention device for added protection.

Learn More

The Octa-Bubbler is an eight-outlet, pressure compensating, low-flow irrigation device. Along with 8 flow-controlled swivel barbed outlets, it has a 1/2” FPT inlet thread base for installation on standard risers, and a backflow prevention device for added protection.

Learn More

The Octa-Bubbler is an eight-outlet, pressure compensating, low-flow irrigation device. Along with 8 flow-controlled swivel barbed outlets, it has a 1/2” FPT inlet thread base for installation on standard risers, and a backflow prevention device for added protection.

Learn More

Push-fit plastic fitting for the connection of plastic, copper, and CPVC pipe. Designed, manufactured and assembled by John Guest Speedfit. Simply push the fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. Should the need arise to demount the connection unlock the nut and push the collet towards the body of the fitting and pull the pipe to release. The fitting ensures an easier working environment in confined places, is approved for behind the wall installations, and removes the need for hot works on site. Installation can be reduced by around 40% when compared to traditional fixing methods. Learn More

Push-fit plastic fitting for the connection of plastic, copper, and CPVC pipe. Designed, manufactured and assembled by John Guest Speedfit. Simply push the fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. Should the need arise to demount the connection unlock the nut and push the collet towards the body of the fitting and pull the pipe to release. The fitting ensures an easier working environment in confined places, is approved for behind the wall installations, and removes the need for hot works on site. 3/8 in Quick Connect Inline Shut Off Valve. This is used to shut off feed or outlet line to system. This valve is for the Evolution RO1000™ and Tall Boy™ system. Learn More

Push-fit plastic fitting for the connection of plastic, copper, and CPVC pipe. Designed, manufactured and assembled by John Guest Speedfit. Simply push the fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. Should the need arise to demount the connection unlock the nut and push the collet towards the body of the fitting and pull the pipe to release. The fitting ensures an easier working environment in confined places, is approved for behind the wall installations, and removes the need for hot works on site. Installation can be reduced by around 40% when compared to traditional fixing methods. Learn More

Push-fit plastic fitting for the connection of plastic, copper, and CPVC pipe. Designed, manufactured and assembled by John Guest Speedfit. Simply push the fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. Should the need arise to demount the connection unlock the nut and push the collet towards the body of the fitting and pull the pipe to release. The fitting ensures an easier working environment in confined places, is approved for behind the wall installations, and removes the need for hot works on site. Installation can be reduced by around 40% when compared to traditional fixing methods. Learn More

A 12" stainless steel coil that is designed to be used with a water-cooled system. Chilled fresh water is pumped through the coil which should be submerged in the nutrient reservoir. The fresh water used to cool the reservoir does not mix with the water in the reservoir. Learn More

More effective irrigation of all types of pots/containers in all growing mediums. Drip emitters and stakes only provide a single point of irrigation making it hard for water/nutrient solution to evenly saturate a container. The water ring has 54 perfectly positioned pores to evenly irrigate containers eliminating dry pockets of growing medium. Kit contains 3 removable stakes to keep water rings in place around each plant. The water ring can also be used without the stakes if desired. The water ring has a 1 inch gap on one end to allow it to be placed around large plants without damaging the stalks. Can be used indoors or out in soil or hydroponics. Durable construction allows for years of use. Can be easily cleaned between growing cycles. Create your own flexible irrigation kits easily and cheaply with any ½ inch I.D. tubing and ½ inch fittings (not included). Please note that adding ½ inch ball valves may be necessary to create an even flow to all water rings in large installations. Learn More

Hydro Flow™ In-Line Flag Emitters allow water to flow smoothly at the designed GPH. The flags are removable and separate easily to allow for cleaning. Works with Hydro Flow 3/16" ID Poly Tubing. Learn More

An essential part for do-it-yourselfers! This float valve assembly controls the water/nutrient solution level in your primary reservoir (controller). Comes with 1/2 brass barbed fitting. Learn More